Montigo 36DV-SH Spécifications télécharger pdf (Page 3)

11/93

Page 3 of 13

INSTALLATION OF DIRECT VENT

A complete Montigo 36DV-TV vent system may comprise of six

individual components: (see figure 5. page 4)

A - Termination MTK-5 (5" length)

MTK-9 (9" length)

B - Stucco Kits MSR (stucco frame)

MOSR (stucco can)

C - Solid section & elbow MIHR-6 (6 ft. length)

MIHR-10 (10 ft. length)

D - Flex sections MFL-1 (1' 6" section)

MFL-2 (2' 6" section)

MFL-3 (3' 6" section)

MFL-4 (4' 6" section)

E - Solid sections MEXT-1 (1' 6" section)

MEXT-2 (2' 6" section)

MEXT-3 (3' 6" section)

MEXT-4 (4' 6" section)

F - 90 degree elbow MEL90 (90 deg. elbow)

Example: For our shortest venting configuration use compo-

nents A, B, and F. (see Figure 5).

Example: A 10' section and elbow (MIHR-10) used in

conjunction with 3 ft. flex section (MFL-3) will, when extended

in a five foot chase, allow for a maximum horizontal run of

twelve and one-half feet from the centre of the fireplace to

outside wall and a minimum of 7'6" when retracted in opposite

direction (see Figure 6 and 7).

"D" flex sections and "E" solid sections may be used in

conjunction with one another to obtain different possible

horizontal length installations. NOTE: Flex section must not

exceed maximum horizontal length of 3 feet. (see Figure 7.1)

Note: DO NOT STRETCH flexible connector to gain

extra length. These connectors are Flexible only to

allow for directional changes, which must not exceed 90

degrees.

A minimum height of 43" to centre of horizontal flue is

required.

All vent pipes must maintain a minimum of 1"

clearance to combustible materials.

Note: It is imperative for satisfactory operation of the

Montigo 36DV-TV fireplace that no venting component

be modified in any way. All components have been

manufactured to eliminate the need for modification

when properly selected and installed.

CAUTIONS AND REQUIREMENTS

DIRECT VENT TERMINATION LOCATION

This section is used to determine where your direct

vent termination will be located.

VENT TERMINATIONS SHALL NOT BE RECESSED IN

WALLS OR SIDING.

CAUTION

1). Extremely important: In heavy snow areas take extra

care to prevent against blocking vent termination with

snow removal equipment.

2). Flue gases exiting vent terminals are very hot and must

not be restricted to assure fireplace combustion is not

affected.

3). Do not place, build any obstruction, plant any bushes

or for any reason attempt to conceal the vent

termination. To do so will affect the operation of

the fireplace and may be hazardous.

4). National Standards require that vent terminations be

protected with an additional screen on patio's, decks and

any areas accessible to public. For maximum safety we

recommend all terminals below 7' from grade level be

installed with a certified Montigo protective screen. (MTKG)

FIGURE 4. VENT TERMINATION FRAMING.

MTK-5 or MTK-9 MTKO-5 or MTKO-9

IMPORTANT:

When using MTK or MTKO with

MOSR: Framed opening must be 12"

X 12"

When using MTK or MTKO:

Framed opening must be 11" X 11"

FOR DETAILED SKETCH OF ALLOWED

TERMINATION LOCATIONS SEE APPENDIX A

FOR VINYL SIDING APPLICATIONS ALL MTK

TERMINATIONS MUST BE INSTALLED WITH A

HEAT SHIELD (MTKG) TO PROTECT THE SIDING

FROM ANY HEAT DAMAGE. MTKO TERMINATIONS

DO NOT REQUIRE A HEAT SHIELD.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Montigo 36DV-SH Spécifications Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Foyers Montigo 36DV-SH